You open the door of your front-load washer and get hit with a musty, mildew smell — and sometimes your “clean” towels smell the same way. This is one of the most common complaints we hear about front-load washers, and the good news is that most of the time it’s something you can fix yourself in under an hour, without tools.
Front-load washers seal tightly and use very little water. That’s great for efficiency, but it also means moisture, lint, and leftover detergent can sit in a few hidden spots and grow mildew. Here’s where to look, in the order we’d check it.
Safety first
- Unplug the washer before reaching into the drain pump filter or pulling out the dispenser drawer.
- Never mix cleaners. Bleach combined with vinegar, ammonia, or some other cleaning products releases toxic gas. Use one product at a time and run a rinse cycle in between.
- Wear gloves — what’s living in the door seal is not something you want on your hands.
- If you smell burning or electrical odors rather than mildew, stop using the washer, unplug it, and call a technician. That is not a DIY situation.
1. Clean the door gasket (the rubber seal)
This is the number-one source of washer odor. Pull back the folds of the rubber boot all the way around the door opening. You’ll often find standing water, hair, lint, socks, coins, and black or gray mildew.
Wipe out the debris, then clean the folds with a cloth and a mild solution — your washer’s manual will list what the manufacturer recommends (many suggest a diluted bleach solution). Dry the folds with a towel when you’re done.
If the mildew has stained deep into the rubber or you see a tear in the seal, cleaning will only help so much. A torn or permanently stained gasket can be replaced.
2. Clean the drain pump filter
Most front-load washers have a small access panel near the bottom front corner. Behind it is a drain pump filter (sometimes called a coin trap) that catches lint, hair, and small objects. When it gets clogged, dirty water sits in the bottom of the machine — and that water smells.
Before you open it: unplug the washer, lay down plenty of towels, and have a shallow pan ready. Water will come out, sometimes more than you expect. Many models have a small drain hose next to the filter that lets you drain the water slowly first. Unscrew the filter, clean it out, and screw it back in snugly so it doesn’t leak.
3. Clean the detergent dispenser drawer
Pull the dispenser drawer out completely (most have a release tab). Detergent and fabric softener residue builds up in the drawer and in the cavity behind it, and mildew loves it. Rinse the drawer in a sink with warm water and an old toothbrush, and wipe out the opening it slides into.
4. Run a tub-clean cycle
Most front loaders have a “Tub Clean” or “Clean Washer” cycle. Run it with the tub empty, using either a washer-cleaning tablet or the cleaner your manual recommends. If your washer doesn’t have this cycle, use the hottest, longest setting with an empty drum. Doing this about once a month helps keep the smell from coming back.
5. Change a few habits
- Leave the door and dispenser drawer cracked open between loads so the inside can dry out (keep it closed if you have small children or pets around).
- Use HE detergent, and less of it. More soap doesn’t mean cleaner clothes. Extra detergent leaves residue that feeds mildew. Follow the line on the cap, not the top of the cap.
- Go easy on liquid fabric softener, which also leaves a film behind.
- Move wet clothes to the dryer promptly. A load left sitting overnight can make both the clothes and the drum smell.
- Wipe the gasket dry after the last load of the day.
When it’s time to call for help
If you’ve done all of the above and the smell is still there, something else is likely going on. Call a technician if you notice:
- Water still sitting in the drum or the filter area after a cycle finishes — that can point to a failing drain pump or a blockage further down the line.
- The washer won’t drain or stops mid-cycle with an error code.
- A torn door gasket, or mildew you can’t clean out of the seal.
- A sewage smell rather than a mildew smell. That’s often a drain or venting issue in the home’s plumbing rather than the washer itself, and a plumber may be the right call.
- Any burning smell — stop using the washer and unplug it.
If you’d like us to take a look, we service front-load and top-load washers in Denton and the surrounding area. The $99 service call applies to the total cost of the repair if you choose to fix the appliance.
Learn more about our washer and dryer repair in Denton, TX, or call us at (940) 286-4094.